Cep telefonunuzdan yolladığınız mesajın ulaşıp ulasmadigina dair bir bilgi
almak isterseniz mesajinizin basina *00# bosluk yazıp
yollayınız.Mesajınız karsi tarafa ulaşınca size de ulaştırıldığına dair gsm
operatörünüzden mesaj gelir.
Telefonunuzun IMEI numarasını öğrenmek için * # 0 6 #
tuşlayınız.
Telefonunuzun software versiyonunu görüntülemek için * # 0 0 0 0
# tuşlayın.
Telefonunuzun yazilim versiyonunu ögrenmek için:
-> -> * <-
<- * <- * ( 2kere sag ok yildiz 2kere sol ok yildiz sol ok yıldız )
tuşlayınız.
Bir daha sol oka basarsaniz cep telefonunuzu o anki dilde
programlar.
Telefonunuzu dilini hemen ingilizce isterseniz: *#0000#
PIN1'i değiştirmek için: **05* PUK * yeniPIN1 * yeniPIN1#
PIN2'i değiştirmek için:**052* PUK2 * yeniPIN2 * yeniPIN2 #
Arama yönlendirme: **004* yönlendirilecek_numara #
Telefonunuzun IMEI (seri numarasi) ni ögrenmek için ; *#06#
Telefon defterinde sira nosunu bildiginiz birisini aramak için ; sira
nosu #
Örnek: 12#
Ayrica ilk 9 sıradaki telefonları ararken hiç #(kare) ye basmadan
direk yes tuşuna basarak arayabilirsiniz.
ERICSSON GA 628
Kodları
Telefonunuzun IMEI numarasını görmek için * # 0 6 # tuşlayın.
Yazılım
versiyonunu görüntülemek için -> * <- <- * <- * tuşlayın.
Son
çevirdiğiniz numarayı tekrar aramak için 0 # tuşlayın.
Telefonunuzun
dilini ingilizceye çevirmek için * # 0 0 0 0 # tuşlayın.
Batarya şarjı
durumunuzu telefon kapalı iken öğrenmek için açma kapama düğmesi olan NO
tuşuna kısa bir süre basıp çekin
ERICSSON 688 - 888
Kodları
IMEI kodu * # 06 #
Yazılım ve üretim tarihi > * < < * < *
İngilizceye Menü *#0000#
Batarya Telefon kapalı iken batarya durumunu
görmek için NO tuşuna basıp 2 saniye bekleyin.
Servis Sağlayıcının tam
ismi Network menüsüne gidip Serves sağlayıcıların ismi ekrana geldiğinde *
tuşuna basın
Bağlantı Kablosu 1 = + external power supply (7.2Volt -
600mA)
2 = RS232 input (TTL)
3 = GND (digital)
4 = RS232 output
(TTL)
5 = +5V output
6 = Test (0=Normal - 1=test mode)
7 = Mute
8 = Internal/external mic and ear (0=External - open=Internal)
9 = GND
(analogic)
10 = ?
11 = BF in
12 = BF out
Ericsson 788 Kodları:
(English)
To view IMEI number *#06#
To view Software Version enter * -> *
<- <- * <- *
Service Provider Lock is * <- <- * but it
is now called the ME lock.
There are two options after selecting yes
on another menu. These are lock to Network or lock to NetSubet.
Command
set
The following commands are recongnized by the phone.Use 9600 baud,
1 stopbit, 8 data bits, no parity.
ATA Pick up phone during
ring
AT+GMI Manufacturer identification
AT+GMO Request model
Identification
AT+GMR Request revision Identification
AT+GMM
ATDxxx;
Dial number xxx
ATH Hangup phone
AT+CFUN=? Define levels of
fuctionality in the order of power consumed
AT+CFUN=0 Switches off the
phone
AT+CBC Query battery level
Each command has to be followed by
a 0x0A, 0x0D sequence, that is carriage return - line feed.
These
commands will be ackowledged with an 'OK' prompt. An
incoming call is
signalled by the string 'RING' sent by the phone at 9600b in normal
mode.
Portable Handsfree Unit
1 Earphone: 16 Ohm
2
Microphone: <- 2 kOhm
5 Connected to 04 (GND)
Pinouts
Left to right, keyboard up
1 Audio Out
2 Audio In
3 Accessory
Sense. GND to enable External Mic and Speaker (Analog)
4 Audio Signal
GND.
5 Portable handsfree In.
6 Music Mute Out, High when phone is
used.
7 In Flash Memory Voltage and Service Voltage, In 0V=normal,+5V=test,
+12V=test+flash
8 Logic Out, Status On. Sources over 100mA
9 Data Out
from Mobile Station. Debug messages appear here at 112KBaud when in debug
mode.
10 Digital Ground and DC return
11 Data in
12 DC in for
battery charging, DC out for accessory power
ALCATEL
ALCATEL One Touch Easy Kodları:
IMEI kodu * # 06 #
*#000000# Servis Menüsüne giriş
Gizli menüyü
görmek için 000000 yazın ve * a basın
Gizli menü:
TRACES - "Channel
indicator" menus
ARRETS - I Dunno
VIDER ARRETS - Ok a basin : This
action is executed!
CTRL CHARGE - şarjın ve bataryanın voltajını
gösterir
DAMIER - Görüntü testi
BOSCH
(English)
Bosch 738 - Bosch 718, Bosch COM 607 - 908
Kodlari:(English)
*#06# to display the IMEI
*#0000# to set the language
automaticaly (To english)
*#3370# to set the Enhaced Full Rate
#3370#
to Reset the phone
*#9000# to enter sim lock code
*#9003# to enter the
network code
*#9004# to enter the subset code
*#9100# to remove the sim
lock permanently
*#9101# to remove the corporate lock
permanently
*#9102# to remove the provider lock permanently
*#9103# to
remove the network lock permanently
*#9104# to remove the subset lock
permanently
Reveal Engineering Menu
Press *#3262255*8378# (equivalent to
*#DANCALL*TEST#) to make secret Engineering menu (Menu 10) appear. Then you
will be able to see the following information.
10. Engineering
10.1 MS
Info
10.1.1 on
10.1.2 off
10.2 Software details
10.2.1 Software
version
10.2.2 EEPROM version
10.2 Test / Production details
10.3.1
Hardware data
10.3.2 Production data
10.3.3 Service data
10.3.4
Mechanical data
MOTOROLA
(English)
MOTOROLA 6200/7500/8200/8400/8700
Kodlari:(English)
To activate RBS (Engineering Menus):
[pause] [pause]
[pause] 1 1 3 [pause] 1 [pause] [ok]
(pause means the * key held in until
box appears)
You now have to press the [MENU] and scroll to the 'Eng Field
Options' function with the < or > keys, and enable it.
To de-activate
RBS (Engineering Menus):
[pause] [pause] [pause] 1 1 3 [pause] 0 [pause]
[ok]
(pause means the * key held in until box appears)
Works on
6200's,8200's,1-888's,7500's,8400's and GSM StarTacs with later than version
.27 software.
Options under Eng Field Options
Eng Field
Options
Active Cell
RxLev -55 Received powerlevel in dBm
NCC 0
National Colour Code, used for identifying channel
BCC 7 Broadcast Colour
Code, also for identifying purposes
MSTxPwr 35 Max allowed transmit power
35dBm about 3.2W
C1 003 Is a calculated figure for the quality control
signal which is constantly sent out from the RBS quality the signal returning
from the phone has. If this value is negative for more than 5 sec then the
system will make a cell switch.
Time Adv xxx xxx is a number. Multiply this
number by 550, and the result is the distance from the RBS (Radio Base
Station), in meters.
Adjacent Cells
Adj Cell 1
Channel 0033 Channel
Number
RxLev -65 Received powerlevel in dBm
BCCH Decode I think it means
it is able to decode the channel information contained in the BCCH
RxLevAM
-104 Min allowed reception, compare with RxLev -65 and you get the C1 value
which is 39 and reported back to base as measure of field strength.
MTxPwr
35 Aain max allowed powerlevel
C1 003 ??
NCC 0 National Colour
Code
BCC 6 Broadcast Colour Code
System Parameters
Combined Off
??
AcsClas 0000 Allows different priorities - this network doesn't support
it.
MCC 505 Mobile Country Code, 505 for Australia, 240 for Swedes
etc
MNC 01 Mobile Network Code, 01 for Mobilenet, 02 for Optus, 03 for
Vodafone using MCC 505. MCC+MNC is often called Network Code
LAC 08720
Location Area Code, shows which exchange your're in
CellID 00473 Base
Station Identity
T3212 005 Time between periodic network updates (either
hours between or time remaing until update, not sure)
BS-PA-MFRM 4
??
XZQTY 14.3 ??
Motorola Flip Pinout:
ANT- (O) | | | | | | | | |
|
10 9 8 7 6 5 4 3 2 1
Top of phone (screen)
1) Audio Ground
2)
Ext b+
3) T Data
4) C Data
5) R Data
6) Logic Ground
7) Audio
Out - on/off
8) Audio In
9) Manual Test
10) Battery Feedback
PHILIPS (English)
Philips
DIGA Kodlari:
Blocking list *#3333*#
Time connected *#2558*#
Flags,something *#3377*#
Security code *#7489*#
Philips FIZZ
phones:
IMEI code *#06#
SW info *#8377*#
Security code *#1234*#
Philips SPARK phones:
IMEI: *#06#
Philips GENIE Kodlari:
*#06#
IMEI number
*#2254*# Status register: C, BS, RR, MMI, CREAT.
*#2255*#
activate and deactivate the "DEBUG CALL"-Mode; when activated, make a call to
a busy line an the phone will display some hex-codes on the
display
*#2558*# the time in days,hours and minutes you are connected to
the net
*#2562*# not clear; the phone reconnects to the net
*#2565*# not
clear; warmstart
*#3333*# (NO) BLOCKING - list (15 items)
*#2377*#
"BEER": not clear, the phone waits a random time and reconnects to the
net
*#3377*# Init, Flags, SIM LCK
*#3353*# resets the (NO) BLOCKING -
list
*#7378*# Name, Length, SIM phase
*#7489*# SECURITY CODE
*#7693*#
activate and deactivate the SLEEP MODE (when deactivated the battery will go
down!)
*#7787*# SPURIOUS INTERRUPT
*#7948*# SWITCH OFF
*#8463*# Some
information about the SLEEP MODE: Wake, Sleep Req., Sleep
Pinouts for
Philips Fizz and Spark
1 GROUND
2 GROUND
3 HANDS FREE ON/OFF
4
MUTE
5 TX
6 RX
7 RTS
8 REPROGRAMMING
9 ON HOOK CHARGER
10
AUX MIC
11 AUX SPEAKER
12 GROUND
SONY
Sony CMD-Z 1Kodları:
Press *#06# to view IMEI
Show Software version
and manufacturing date : Press # 8377466 # (#version#)
Sony CMDX
1000
Show Software date : Remove your SIM Card, then press : * # 06
#
and finally press:
[left softkey]
To enter Monitor Mode on Network
Option menu:
Menu
9 (Phone Options)
7 (Phone Status)
[Left Display
Button] (left MENU key) 7684666 [HangUp Button] (Red HandSet key)
Some
characters explained
* activate
** register and activate
*# check
status
# unregister
## unregister and deactivate
Call barring
**33*code# Activate barr all outgoing calls (for code see "Safety" above)
#33*code# Deactivate barr all outgoing calls
*#33# Check status of
barr all outgoing calls
**330*code# Activate barr all calls
#330*code#
Deactivate barr all calls
*#330*code# Check status of barr all calls
**331*code# Activate barr all outgoing international calls
#331*code#
Deactivate barr all outgoing international calls
*#331*code# Check status
of barr all outgoing international calls
**332*code# Activate barr all
outgoing international calls except home country
#332*code# Deactivate
barr all outgoing international calls except home country
*#332*code#
Check status of barr all outgoing international calls except home country
**333*code# Activate barr all outgoing calls
